Heck TRACE-A-PUNCH Duplicators Model 3C

Models
at a glance
Specifications

Models and Accessories
3C	TRACE A PUNCH NIBBLER 3C
4	TRACE A PUNCH NIBBLER 4
ROUND HIGH SPEED STEEL PUNCHS
015-M2	ROUND HIGH SPEED STEEL PUNCH M2 GRADE
018-M2	ROUND HIGH SPEED STEEL PUNCH M2 GRADE
025-M2	ROUND HIGH SPEED STEEL PUNCH M2 GRADE
025-M4	ROUND HIGH SPEED STEEL PUNCH M4 GRADE
031-M2	ROUND HIGH SPEED STEEL PUNCH M2 GRADE
031-M4	ROUND HIGH SPEED STEEL PUNCH M4 GRADE
035-M2	ROUND HIGH SPEED STEEL PUNCH M2 GRADE
035-M4	ROUND HIGH SPEED STEEL PUNCH M4 GRADE
ROUND HIGH SPEED STEEL DIE BUTTONS
016-M2	ROUND HIGH SPEED STEEL DIE BUTTON M2 GRADE
019-M2	ROUND HIGH SPEED STEEL DIE BUTTON M2 GRADE
026-M2	ROUND HIGH SPEED STEEL DIE BUTTON M2 GRADE
026-M4	ROUND HIGH SPEED STEEL DIE BUTTON M4 GRADE
032-M2	ROUND HIGH SPEED STEEL DIE BUTTON M2 GRADE
032-M4	ROUND HIGH SPEED STEEL DIE BUTTON M4 GRADE
036-M2	ROUND HIGH SPEED STEEL DIE BUTTON M2 GRADE
036-M4	ROUND HIGH SPEED STEEL DIE BUTTON M4 GRADE
SQUARE HIGH SPEED STEEL PUNCHS
021-M2	SQUARE HIGH SPEED STEEL PUNCH M2 GRADE
045-M2	SQUARE HIGH SPEED STEEL PUNCH M2 GRADE
SQUARE HIGH SPEED STEEL DIE BUTTONS
022-M2	SQUARE HIGH SPEED STEEL DIE BUTTON M2 GRADE
046-M2	SQUARE HIGH SPEED STEEL DIE BUTTON M2 GRADE
DIE RETAINERS
200	DIE RETAINER FOR MODEL 3
240	DIE RETAINER FOR MODEL 4
MATERIAL CLAMPS and SUPPORTS, STRIPPER FOOT, CIRCLE CUTTING ATTACHMENT
300	MATERIAL CLAMPS
220	MATERIAL SUPPORT RING, 2" DIA
230	MATERIAL SUPPORT RING, 3" DIA
400	STRIPPER FOOT
450	CIRCLE CUTTING ATTACHMENT

This is the easiest, most economical way to produce low production metal and plastic profiles. Trace-A-Punch follows your guided template to produce burr free straight and contoured outlines and holes. Simple, rugged meehanite casting construction insures very little maintenance.

An existing part can be used as the master pattern or one can easily be made by tracing over acetate-plastic .020-1/2 inch with a sharp scriber or razor knife. An office copier can be used to produce a master by copying on to Mylar-plastic and cutting with scissors.

All Trave-A-Punch comes complete rerady to run with one #031 (.312) M2 Punch and Die Set,two material clamps, work light, wrenches and Instructions

Model	3C	4
Cutting Capacity Mild Steel Plastic	1/8 inch .125 inch 3.175mm	3/16 inch .186 inch 4.725mm
Cutting Capacity Stainless Exotic Metals	1/8 inch .125 inch 3.175mm	1/8 inch .125 inch 3.175mm
Throat Depth	6-3/4 inch 171mm	16 inch 406mm
Strokes per minute	1750	1200
Motor	1-1/2HP 110/220V 1 Phase - 50/60 HZ	3HP 220/460V 3 Phase - 50/60HZ
Weight	130 pounds - 59kg.	480 pounds - 218kg.


3C Trace A Punch	4 Trace A Punch

Heck TRACE-A-PUNCH Duplicators Model 3C,